Ford Taurus Forum

02 Auto High Beam 03 Autolamp Delay 05 Easy Entry 06 Remote Windows 09 Auto Lock 10 Auto Unlock 13 Rain Sense Wipers All confirmed on setting screen.But turning on the setting manual does not mean the function will work. Auto High Beam, Autolamp Delay and Rain Sense Wipers does not working cus I do...

Confirmed changes on a 2016 Interceptor Sedan (checksum may decode differently in ForScan): 720-01-03 - Change to --- 90E8 00CB A26E <--Turns on remote start options in cluster, turns on auto lock options in cluster (auto locks are still non-functional, though) 726-19-01 - Change to --- 01 47 <--Act...

For those of you looking to run LED replacement bulbs in the front turn/parking or rear turn/brake positions, these are the ForScan edits required to turn off the bulb outage indicators (Hyperflash): In the BCM - Line 726-13-01 change to: 0000 0000 Line 726-14-01 change to: 0000 0000 That's it. 8)

The typical point of failure in the PTWW lights is the module that's built in to the harness, which is part of the light itself. If you want to replace the module, you'd have to find a known good one and splice it into the light harness, as they're all (light, harness, module, plug) a single piece a...

Keyless entry , remote start and intelligent awd monitor done and confirmed. Has anyone done the compass or navigation ... or anything else that can be upgraded / programmed I was successful with both the compass and the awd monitor, but they seem to be mutually exclusive using the settings I've tr...

From what I can tell, you won't be able to get the lock/unlock in/out of park due to the fact that the power door locks aren't BCM controlled in the PI the same way they are in the retail cars.

trife86 wrote:Nevco, you wrote 726-19-01 0147 so are you only changing the first 4 digits of that line? its not a full line of code?

That line the whole thing is only 4 digits.

So this combination will give you keyless PLUS remote start? (I know that might be a silly question, but just being thorough) And is this for '13/early' 14, '14 up, or all? Kyle This was done on a '16, that was factory equipped with keyless - I had to add the hood switch & integrated key fob, but t...

Here's the ForScan edits for enabling remote start (the above is for the keyless entry only):

720-01-03 90E8 00CB A2

726-19-01 0147

crownedking wrote:correct

mid-2014-through 16 enable below:

726-18-01 0100 0008 4F

720-01-03 8088 0000 33

Can you confirm both worked or did one work and the other didn't? What remotes are you using?

That's to enable the remote start?

What you really want to look at is engine hours & idle time - you should be able to access that through the dash menu. According to Ford engineering, 1 hour = 33 miles, so take that into consideration.

The 3.7 cars are no slouch, but the turbo cars are stupid fast - take the turbo if the choice is up to you.

I personally haven't managed to find the proper edits to make with FORScan yet to accomplish this.

You have to make sure the load rating of the resistors + the LEDs is very similar to what the original bulbs were, the resistors that are available out there can vary widely depending on manufacturer. Best bet is to test the resistance across the circuit with the original bulb prior to modification,...

Right, I've got FORScan and have already successfully changed the DRL settings, added the AWD gauge, etc. I'll get the key & hood switch ordered and anxiously await your results...

Just to make sure I'm completely clear - on a '16 PI sedan with factory keyless, the only thing I need for enabling the remote start is the proper transmitter key, and the hood switch? No actual programming changes through FORScan?