If you shop at Amazon.com (for anything), use this link to support FordTaurus.net!

Intro - Looking for Wiring Schematics

Post Reply
mope
Regular Member
Posts: 162
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Intro - Looking for Wiring Schematics

Post by mope » Fri Oct 14, 2016 8:22 pm

Hi all - first post.

I just picked up a 13 interceptor. I'll be documenting my customizations; hopefully some of this stuff might help people in the future......

I started with the center console mod and ended up picking up most of the interior out of a 2010 limited. The rear seats required some massaging, but the fronts are proving more frustrating. Does anyone have the wiring schematics for a 2010 civi and 2013 muni (the pinouts for seat connector especially)?

My interceptor had a manual passenger seat and power driver - transplanting the civi interior throws off the airbag warning. Off the top, the interceptor has the pretensioner in pillar and the civi has it integrated to seat, the civi has a fuel pump/airbag module, and the passenger seat weight sensor is different. I'm working through it, but knowing what's running into, and through, that module would make the job that much easier.

Oh, and my new driver seat is a memory seat....doh! I've got a plan for that one, though.


User avatar
Webmaster
Site Administrator
Posts: 2131
Joined: Tue Jan 06, 2004 11:16 pm
Vehicle: 2002 Ford F-150 XLT SuperCrew
Contact:

Re: Intro - Looking for Wiring Schematics

Post by Webmaster » Fri Oct 14, 2016 9:39 pm

Welcome! This is my go to site for wiring diagrams: http://www.revbase.com/BBBMotor/Wd
2000 Ford Taurus SEL (excellent car, sold to a friend)
1992 Mercury Sable GS (good car except for the tranny, sold)
Current: 03 F150 King Ranch SuperCrew
Other Fords owned: 02 F150 SuperCrew 4x4, 11 F150 EcoBoost, 07 Ranger, 01 F150 XLT, 98 F150 XLT, 96 Thunderbird LX, 95 Escort GT, 86 Mustang LX, 82 Mustang

mope
Regular Member
Posts: 162
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: Intro - Looking for Wiring Schematics

Post by mope » Thu Oct 20, 2016 3:59 pm

Sweet....thanks.

mope
Regular Member
Posts: 162
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: Intro - Looking for Wiring Schematics

Post by mope » Thu Oct 27, 2016 3:07 pm

Ok..... was looking to bypass the sync module in the center console and hook the aux input plug straight to my radio ACM jumpers. However, theres a 5th wire leaving the sync harness up the aux input sub loom - they ran an open ground half way up the aux sub harness and sheathed in aluminum tape. Opinions.... why???

Any reason to preserve the earth or can I just jump the 4 aux input wires as planned?
WIN_20161027_142829.JPG
WIN_20161027_142829.JPG (461.13 KiB) Viewed 1452 times

mope
Regular Member
Posts: 162
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: Intro - Looking for Wiring Schematics

Post by mope » Thu Oct 27, 2016 5:22 pm

Noise cancelling for ground loop on an audio input line?? Well, I'm hooking in my jumpers and well see how it goes.

mope
Regular Member
Posts: 162
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: Intro - Looking for Wiring Schematics

Post by mope » Tue Nov 08, 2016 12:11 pm

Alright.....I'll create a new post detailing my interior conversion once I finish up my new dome light and forscan mods (fyi: more work than initially planned.....I had a few beers after beating the seat wiring/safety restraint system!!) .

In the interim, anyone interested in a pair of pillar covers/integrated speakers? I got two pairs (both tan) and painted all with SEM carpet/cloth. They paint up well, cover the hole from the pillar flood lamp(s), and add tweeters to the sound system. The grates were removed, speakers taped off, and grates painted with plastic spray. This set comes with the male/female speaker plug.......I didn't get the female plug on the set I used and had to solder the speaker wires together. $47 shipped for the pair.
20161108_075556.jpg
20161108_075556.jpg (473.51 KiB) Viewed 1395 times
20161108_075532.jpg
20161108_075532.jpg (475.22 KiB) Viewed 1395 times
20161108_075720.jpg
20161108_075720.jpg (541.05 KiB) Viewed 1395 times

mope
Regular Member
Posts: 162
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: Intro - Looking for Wiring Schematics

Post by mope » Thu Jan 05, 2017 11:33 am

Well, after the holidays I've had some time to finish up the last of the interior updates so I'll start another thread on that conversion.......

in the meantime, anyone interested in oem interceptor hub caps?
CIMG9269.JPG
CIMG9269.JPG (1.12 MiB) Viewed 1250 times

ChargerRT345
Regular Member
Posts: 12
Joined: Mon Jan 02, 2017 8:58 am
Vehicle: 2013 Ford Interceptor Utility

Re: Intro - Looking for Wiring Schematics

Post by ChargerRT345 » Fri Jan 06, 2017 12:16 pm

Interested in those centercaps, how much?

mope
Regular Member
Posts: 162
Joined: Mon Oct 03, 2016 4:11 pm
Vehicle: 2013 Interceptor

Re: Intro - Looking for Wiring Schematics

Post by mope » Sat Jan 07, 2017 5:06 pm

PM me an offer......I don't see any comps on ebay (they're listing the CV centers as Taurus PI?)

Jake_Blues
Regular Member
Posts: 75
Joined: Sun Jan 27, 2019 8:25 pm
Vehicle: 2013 Police Interceptor Sedan

Re: Intro - Looking for Wiring Schematics

Post by Jake_Blues » Thu Jun 06, 2019 8:11 pm

mope wrote:
Tue Nov 08, 2016 12:11 pm
..I had a few beers after beating the seat wiring/safety restraint system!!) .
so, how did you beat the seat wiring/safety restraint issues?

i want to put leather heated front and rear seats in my 2013 as well.

tips please?

Post Reply